Parts & Accessories
$1.95 - $5.95
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture
- Replacement steel quick release skewers
- Replacement rear skewer - Spacing: 135mm - Material: Steel
- Converts Schrader rims to Presta - Rubber - Sold individually
Stan's Downhill Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
$14.95 - $19.95
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
$26.00 - $27.95
Switching to tubeless or in need of valve replacements? Serfas Tire RX replacement valves will do the trick. Available sizes of 32mm, 44mm, or 60mm valves with removable cores, extra valve core, and Schrader to Presta adapter with core removal tool. Please note, Due to the multi-step chemical process and variables involved in anodizing, colors may vary slightly between batches produced.
Salsa springs for Flip-Off skewers
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Page 1 of 1